SERVICE PROCEDURES
2027 38mm FLOAT NA3 Glidecore Rebuild
Required Parts
- 803-04-704 Seal Kit: 2027 38 FLOAT NA 3 Glidecore Rebuild, Two Piece Neg Plate
Required Tools
- 398-00-657 Tooling: Bullet, Sealhead To Shaft, FLOAT NA 2
- 398-00-681 2002-017 32 Damper-side and ALL 32-34-36-40 Spring-side Removal Tool
- 398-00-682 2005-017 34-36-40 Damper-side Removal Tool
- 398-00-706 Tooling: Fork Topcap Socket, 32mm V2, 3/8 Drive
- 803-01-324 Kit: Tooling: 2019 Clamps, Grip Damper, Body and Shaft
- 803-04-828 Kit: Tooling: Clamps, 2026, 36 & 36 E-Opt, and 2027 38 Neg Plate
WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.
WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.
WARNING: Never attempt to modify air volume spacers or air shaft assemblies, as this can damage your fork causing a loss of control of the bicycle leading to SERIOUS INJURY or DEATH.
WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.
WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.
NOTE: To adjust travel on a 2027 38mm fork you must replace the entire Air Shaft Assembly with Inner Air Sleeve.
| Part | Description |
| 820-02-749-KIT | Service Set: Air Shaft Assy, 2027 38, 160mm, FLOAT NA 3, 1.345" Bore, Short MCU |
| 820-02-750-KIT | Service Set: Air Shaft Assy, 2027 38, 170mm, FLOAT NA 3, 1.345" Bore, Short MCU |
| 820-02-751-KIT | Service Set: Air Shaft Assy, 2027 38, 180mm, FLOAT NA 3, 1.345" Bore, Short MCU |
| 820-02-629-KIT | Service Set: Air Shaft Assy, 2023 Rhythm 38, 180mm, 1.355 Bore |
| 820-02-630-KIT | Service Set: Air Shaft Assy, 2023 Rhythm 38, 170mm, 1.355 Bore |
| 820-02-631-KIT | Service Set: Air Shaft Assy, 2023 Rhythm 38, 160mm, 1.355 Bore |
| 820-02-632-KIT | Service Set: Air Shaft Assy, 2023 Rhythm 38, 150mm, 1.355 Bore |
Step 1
Remove the blue air cap then use a shock pump to slowly release the air pressure while you hold the lower leg arch down.
Step 2
With the fork slightly inverted (the bottom of the fork up past horizontal), remove the black cover, then use a 2mm hex wrench to remove the red rebound knobs.
Step 3
Use a 15mm socket to remove the damper side bottom nut. Make sure to remove and discard the original crushwasher which may be stuck to the bottom nut.
Step 4
Use a 10mm socket to unthread and remove the air side bottom nut. Remove and discard the original crushwasher.
Step 5
Use Damper Removal Tools 398-00-681 and 398-00-682 to dislodge the shafts from the lowers. Make sure that you have approximately half of the available threads engaged with your tool before striking with your mallet. Remove the damper removal tools, then bring the fork upright over an oil basin to drain. After oil stops draining from the lowers, pull the lowers off of the upper tubes and set them aside.
WARNING: Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.
Step 6
With a chamfer-less 6-point 32mm socket (PN: 398-00-705), unthread the topcap assembly completely. Pull straight up to remove the entire topcap assembly from the left side stanchion tube. Some upward force might be needed to overcome the friction of the stock air volume spacers.
Step 7
Carefully remove the retaining ring from the bottom of the air side upper tube, taking care not to scratch the upper tube. Thread the damper removal tool (PN: 398-00-681) onto the air shaft and pull out from the upper tube to remove the air shaft assembly.
Step 8
Clean the shaft with Isopropyl alcohol then clamp it in your 10mm shaft clamps (PN: 803-01-324). Remove and discard the o-ring from the base stud then carefully apply heat to the shaft at the base stud with a propane torch for 5-10 seconds to break down the Loctite.
Step 9
Unthread the base stud counter-clockwise with a 12mm wrench, then lift up to remove. Remove the remaining o-ring on the base stud and replace with a new greased one from the kit. Lift up on the neg plate to remove it from the shaft.
Step 11
Remove the seal on the outside of the Neg Plate. Clamp Neg Plate using your Neg Plate Clamps (PN:803-04-358)
Step 12
Using Neg Plate socket ( PN: 398-01-298) unthread Capture Plate (CCW) from Neg. Plate Housing.
Step 14
Replace Compliance O-ring with new greased one from the kit. Reinstall Neg Plate Seal Carrier.
Step 15
Apply 1-2 drops of red Loctite 263 to the threaded Capture Plate. Using Neg Plate socket ( PN: 398-01-298) thread on (CCW) Capture Plate onto Neg Plate Housing and torque to 50in/lb. Replace the two seals on the outside of the Neg Plate with new ones from the kit and set aside.
Step 16
Remove quad ring from Upper Piston. Carefully clamp the wrench flats on the lower piston in a soft jaw vice and unthread Upper Piston counter clockwise with a 28mm socket from Lower Piston.
Step 17
Push Piston bolt out from within Lower Piston. Replace Compliance O-ring withing lower Piston and Upper Piston with new ones from the kit.
Step 18
Reinstall piston bolt and shaft thru lower piston.Install new glide band from the kit on upper piston. Apply 1-2 drops of red Loctite 263 to the threads of the lower piston. and thread on upper piston onto lower piston. Torque to 80in/lb with 28mm socket. Install new quad ring from kit.
Step 20
Insert the bullet tool (PN: 398-00-657) into the shaft, then coat it with a thin film of Slick Honey. Reinstall the neg plate with it's flat side down. Remove the bullet tool.
Step 21
Apply 1-2 drops of red Loctite 262 to the threads inside the shaft, taking caution not to get Loctite in the area of the shaft where the base stud o-ring will seat. Insert the base stud and thread it in clockwise, tightening to 50 in-lb (5.7 Nm) torque with a 12mm crow's foot.
Step 23
Apply a thin film of Slick Honey to the inside of the upper tube. Apply a thick film of Slick Honey to the air shaft assembly in the areas of the piston, neg plate, and shaft above the neg plate.
Step 24
Insert the air shaft assembly into the end of the upper tube. Push the air shaft assembly into the upper tube far enough to allow you to start the neg plate into the upper tube. Push the shaft into the upper tube to pull the neg plate into its installed position.
Step 25
Replace the retaining ring making sure it is fully seated in its groove by pulling on the air shaft.
Step 26
Inject 3cc of FOX 20wt. Gold oil into the main air chamber through the top of the upper tube. Reinstall the topcap into the fork crown and tighten clockwise to 220 in-lb (24.8 Nm) torque with your 6-point chamfer-less 26mm socket.
Step 27
Add air pressure to your desired setting using a FOX high pressure pump. See the Setting Fork Air Pressure section for more information. Reinstall the blue air cap.
Step 28
Install the Lower Leg Assembly onto the upper tubes. Inject the approprate amount of bath oil into each leg through the bottom hole. Please reference the bath oil chart for your fork
Step 29
Install a new crushwasher on each side followed by the appropriate bottom nut. Torque air spring bottom nut to 50in-lb (5.7 Nm) and damper bottom nut to 110in-lb (12.4Nm) for Grip X and Grip X2 dampers. 150in-lb (16.9Nm) for Grip damper.

























-m.jpg)
-t.jpg)





-t.jpg)







 copy-m.jpg)
 copy-t.jpg)































































